FranklinWH Battery Installation in the Bay Area: aPower 2 Cost, aGate and Generator Backup
A FranklinWH aPower 2 installed in the Bay Area runs $9,000–$20,000 per unit before incentives, inside the one battery range we publish for every brand. FranklinWH is the system we reach for when the solar is already on the roof, when a standby generator belongs in the plan, or when a hillside home needs backup that keeps growing.
Last updated: November 2026 · Sources: FranklinWH aPower 2 datasheet (SKU APR-10K15V2-US, 2025-07-23), FranklinWH aGate X 1.3 datasheet (2025-10-11), FranklinWH Generator Module datasheet, FranklinWH: components of Franklin Home Power, CPUC Net Billing Tariff, PG&E Base Services Charge, PG&E Public Safety Power Shutoffs
Often paired with: Battery storage · Tesla Powerwall 3 · SPAN smart panel · Residential solar · SGIP waitlist check · Pricing
Further reading: Powerwall 3 vs FranklinWH vs Enphase · Solar payback period under NEM 3.0 · Solar not producing? Service-entry troubleshooting
What a FranklinWH installation costs in the Bay Area
We price every home battery, FranklinWH included, inside the $9,000–$20,000 per unit range on our pricing page. FranklinWH’s hardware pricing is set by the manufacturer and included in our fixed quote; the quote also covers the aGate controller, mounting, conductors and conduit, the permit drawings, the inspection visit and the PG&E interconnection filing. Nothing is added after signature unless you change the scope.
What decides where a FranklinWH job lands inside that range:
- Where the aGate goes. The aGate is the brains and the transfer switch in one box. Mounted at the service entrance beside a 200A main panel with the meter a few feet away, the wiring is short and the price is low. A meter at the street with the panel at the house, a detached garage, or a battery closet on the downhill side of a lot means conduit and sometimes a trench.
- Options you add. The Smart Circuits module and the generator module each add hardware and a page to the drawings. They are worth it when an EV charger, a pool pump or a standby generator is in the backup plan, and not otherwise.
- Your panel. The aGate’s 280A busbar and UL 1741 PCS listing let it manage loads on a service that would otherwise need upgrading, but a corroded or recalled panel still has to go. A 200A upgrade on the same permit is $4,500–$14,000; a SPAN smart panel is the alternative when circuit control is the goal.
- Solar. FranklinWH is AC-coupled, so new solar means a separate inverter or microinverters on top of the battery: $20,000–$50,000 (about $2.50–$3.80 per watt) for the 8–13 kW most Bay Area homes need. Existing solar costs nothing extra to connect.
| Configuration | Hardware | Where it lands | Typical fit |
|---|---|---|---|
| Whole-home backup, existing solar | 1 aPower 2 + aGate | Lower half of $9,000–$20,000 | Retrofit onto an Enphase or string-inverter array; the most common FranklinWH job we do |
| Whole-home with load control | 1 aPower 2 + aGate + Smart Circuits | Middle of the range | Homes with an EV charger, pool pump or AC condenser that should shed when the battery runs low |
| Whole-home with generator | 1 aPower 2 + aGate + generator module | Upper range for the battery; generator and its gas or propane work priced separately | Santa Cruz Mountains, Lamorinda and East Bay hills homes facing multi-day shutoffs |
| Two units | 2 aPower 2 + aGate | Two units, each inside the range | All-electric homes: heat pump, induction range, EV charging and air conditioning through an outage |
Before incentives. The aGate is shared by every aPower 2 on the site, so the second unit costs less than the first. Reviewed November 2026.
Get a Fixed-Price FranklinWH Quote
FranklinWH-certified installer, C-10 licensed, our own crew. One itemized price after a site visit, anywhere in the Bay Area.
CA Lic #1143455 · Tesla Certified Installer · Enphase · Bonded & Insured
✓ 10-year workmanship warranty · ✓ Our own licensed C-10 crew — no subcontractors · ✓ Upfront, no-pressure pricing
Get a Free Quote ☎ (650) 451-8464aPower 2 specs that matter for a Bay Area home
| Usable capacity | 15 kWh per aPower 2; up to 15 units (225 kWh) on one aGate |
| Output | 10 kW continuous, 15 kW peak for 10 seconds, 25 kW transient for 1 second; 185 A locked-rotor start for pumps and compressors |
| Charge rate | 8 kW continuous, on-grid or off-grid |
| Chemistry | Lithium iron phosphate (LFP); 90% round-trip efficiency |
| Coupling | AC-coupled; works with any solar inverter brand, micro or string |
| Placement | Indoor or outdoor, wall or floor mount; NEMA Type 3R enclosure with IP67 battery pack and inverter; flood-rated to 29 inches above the base; fanless, about 30 dBA |
| Operating range | −4 °F to 122 °F, with derated output to 131 °F |
| Warranty | 15 years or 60 MWh of throughput on the battery; 12-year limited on the aGate X; plus our 10-year workmanship warranty |
| App modes | Self-Consumption, Time of Use, Emergency Backup; configured for NEM 3.0 at commissioning |
Two numbers explain why the aPower 2 changed our view of FranklinWH. The original aPower put out 5 kW, enough for essential loads but not for an air-conditioning compressor; the aPower 2 doubles that to 10 kW continuous with a 15 kW surge, so one unit now carries a typical Bay Area house. And the warranty moved from 12 years to 15 years or 60 MWh, the longest term of the three batteries we install. The fanless design matters more than it sounds on a side yard under a bedroom window: there is no fan to hear at 2 am.
The aGate: whole-home transfer switch, load control and energy manager
Every FranklinWH system is built around the aGate, and understanding it is most of understanding the product. It is listed as a microgrid interconnect device, which is the UL way of saying it is the automatic transfer switch: it meters the grid, the solar and the battery, and when PG&E drops it opens the service and lets the aPower 2 carry the house with no flicker at the refrigerator or the router. It mounts indoors or outdoors (NEMA 3R) at the service entrance or beside the main panel, accepts up to 200A of grid input on a 280A busbar, and can even serve as the load center itself on a new build or a panel replacement.
Three features inside the aGate are the ones Bay Area homeowners end up using:
- Smart Circuits. An optional module adds controllable breaker positions, one 80A and up to two 50A circuits, that the aGate sheds automatically during an outage when the battery falls to a state of charge you set (FranklinWH calls it SOC auto cut-off) and that you can also switch from the app. We land the EV charger, the pool pump or the AC condenser there, so a long outage never drains the battery into a load you did not mean to run.
- Generator module. An optional module that lets the aGate start, stop and manage a standby generator, covered in the next section.
- Black start. FranklinWH’s black-start function is designed to recover the battery after a prolonged outage or an extended trip runs it flat, rather than leaving the system stranded until someone visits.
The FranklinWH app is the only control surface you need day to day: live flows for grid, solar, battery and loads, the three operating modes, the backup reserve, Smart Circuit switches, generator schedules and a full-charge command ahead of a forecast shutoff. We set the Time of Use mode for PG&E’s tariff at commissioning so the battery discharges into the 4–9 pm peak from day one.
FranklinWH + generator for hillside homes
This is the configuration no other battery we install does as cleanly, and it is why a FranklinWH quote so often goes to Los Gatos hills, Aldercroft Heights, Saratoga, Lamorinda and the Oakland and Berkeley hills. With the generator module in the aGate, a standby generator becomes a third energy source alongside solar and the battery rather than a separate system with its own transfer switch. You set an upper and lower state of charge in the app. During a shutoff the house runs on the battery and solar; if the weather is smoky or grey and the battery reaches the low mark, the aGate sends a two-wire start signal, the generator takes the loads and recharges the aPower 2, and at the high mark it shuts the generator down. The generator runs for a few hours instead of all week, which is quieter for the neighbors and far cheaper in propane.
The module accepts generators up to 160A continuous on a 200A breaker and works with two-wire start, utility-sense and ATS-type units from the major brands. FranklinWH’s sizing guidance pairs roughly a 12 kW generator with one aPower 2 and about 23 kW with two, and we size to the loads you actually want running. The gas or propane line, the pad and the generator itself are priced separately from the battery; if you already own a standby generator, we integrate it rather than replace it. For a Santa Cruz Mountains home on a well, this combination is the difference between a three-day PSPS that costs a hotel stay and one you barely notice.
Adding FranklinWH to the solar you already have
Most FranklinWH jobs we do are retrofits: solar went on in the NEM 2.0 era, the inverter is still fine, and the homeowner now wants backup and a way to use the evening peak. Because the aPower 2 is AC-coupled and the aGate is rated for micro- and string inverters alike, the existing array simply lands on the aGate’s solar input (80A maximum) and keeps producing exactly as it did; no roof work, no inverter swap, and adding a battery does not by itself move a NEM 2.0 customer to NEM 3.0 (we file it as a storage addition and keep the sizing inside PG&E’s rules). FranklinWH’s own guidance allows about 8 kW of PV per aPower 2, so a large legacy array may call for a second unit to be fully backed up during an outage, which we confirm from your inverter’s nameplate before quoting.
Enphase microinverter homes are the classic case. An Enphase IQ Battery 5P is the in-family option and we quote it too, but it takes three 5 kWh units and an IQ System Controller to reach what one aPower 2 delivers, and the aGate’s generator path has no Enphase equivalent. String-inverter homes (SolarEdge, SMA, Fronius, older ABB) get the same treatment: the inverter stays, the aGate islands it with the house, and the battery holds the midday surplus. If the array is underproducing, read our service-entry troubleshooting guide first; we fix that before we add storage to it.
New solar + FranklinWH works just as well, with a separate string inverter or microinverters feeding the aGate. We quote it for homeowners who want the generator path or the 15-year warranty, and we quote the Powerwall 3 alongside it so the inverter trade-off is in front of you rather than buried in a spec sheet.
PSPS and outages: where a FranklinWH system earns its keep
PG&E’s Public Safety Power Shutoffs are a hillside problem. The high fire-threat districts cover the Santa Cruz Mountains from Los Gatos and Saratoga across to Scotts Valley, the Oakland and Berkeley hills and Lamorinda, the Mt. Diablo foothills, the eastern Santa Clara County hills, and the ridges of Marin and Sonoma, and those are also the neighborhoods where a well pump, a septic lift pump or a long driveway gate make an outage more than an inconvenience. Red-flag shutoffs in October and November can run two or three days; winter storms and equipment faults add shorter outages everywhere, including the flats of San Jose, Sunnyvale and Fremont.
The arithmetic for one aPower 2: 15 kWh carries a refrigerator, lights, internet, a furnace fan and a pump through the night with margin, the array refills it by early afternoon, and the 10 kW output means the well pump and a single AC condenser can share the battery if you are careful about the oven. Add a second unit or a generator on the module and you stop managing anything at all. We set a backup reserve in the app so a normal evening’s peak shaving never leaves you empty when the PSPS notice arrives, and the app’s full-charge command tops the battery from the grid before the forecast event.
NEM 3.0, the Base Services Charge and payback
Under PG&E’s NEM 3.0 net-billing tariff, exported solar earns roughly $0.05–$0.08 per kWh while evening grid power costs several times that, so storing the midday surplus and spending it between 4 and 9 pm is where the money is. The aPower 2’s Time of Use mode does exactly that, and its 8 kW charge rate means a mid-size array fills it before the afternoon is over. Since March 1, 2026 every residential PG&E bill also carries a Base Services Charge of about $24.15 per month (lower for CARE and FERA customers) that no solar or storage can offset; it appears in every model we show you.
For a right-sized solar-plus-battery system we model a 7–12 year payback, and a FranklinWH retrofit onto a paid-off array often lands at the short end because the solar cost is already sunk. A battery without any solar is mainly a resilience purchase; Time of Use mode shifts some grid energy off peak, but the battery cannot create what it stores. Run your bill through the NEM 3.0 savings calculator, read how we calculate payback under NEM 3.0, and use the NEM 3.0 + Battery Buyer’s Guide for the tariff detail.
Incentives for a FranklinWH battery in 2026
Plan the purchase as if no rebate will arrive, then treat any that does as a bonus. The state SGIP program has no open residential battery budget as of September 2026; only the equity waitlist remains, for households under 80% of area median income or on CARE, FERA or ESA, and we file that reservation for you where it applies (check your tier). The 30% residential federal credit is gone for anything placed in service after 2025, though commercial and non-profit owners keep the Investment Tax Credit, depreciation and direct pay. What does remain for every homeowner: California's property-tax exclusion for solar, and $0-down loan, PPA and lease options. The 2026 incentives hub tracks every utility and CCA program.
FranklinWH vs Powerwall 3: when we recommend each
We are certified for both and have no stake in which one you choose, so here is the honest split.
We recommend FranklinWH when solar is already on the roof, because AC-coupling onto any inverter brand is its native mode and nothing about the existing array changes. We recommend it when a standby generator is part of the plan, since the aGate’s generator module is the only integrated, state-of-charge-driven generator control among the batteries we install. It is also the pick for a 15-year warranty, for a quiet fanless unit near living space, and for a home that will keep adding 15 kWh units over the years.
We recommend the Powerwall 3 when you are buying solar and storage together, because its built-in 20 kW solar inverter means the panels wire straight into the battery with no separate inverter, one fewer box on the wall and a simpler permit set. Its 11.5 kW output is a little higher per unit, Tesla owners get one app for car, charger and battery, and the Expansion units add capacity cheaply when power is not the constraint. It carries a 10-year warranty and no integrated generator control.
The three-way comparison with Enphase, specs side by side, is in Powerwall 3 vs FranklinWH vs Enphase; the Tesla installation detail is on our Powerwall 3 page, and circuit-by-circuit sizing is on the battery storage page.
How a Bay Area FranklinWH installation runs
- Walk-through. A year of PG&E bills tells us how much you store and when; the panel, meter and existing inverter tell us how the aGate ties in. If a heat pump, EV charger or generator is coming, the NEC load calculation happens here, not after the permit.
- Fixed quote. aPower 2 count, aGate location, which circuits become Smart Circuits, generator module yes or no, and any panel or trenching work — one itemized number, no allowances.
- Paperwork. Plan set to the city or county, interconnection application to PG&E (an existing NEM 2.0 array is filed as a storage addition, within PG&E's rules). Expect 2–6 weeks, set mostly by the jurisdiction.
- Install. Our own crew, one to two days: aGate at the service entrance, batteries on the wall or floor next to it, solar and generator landed in the aGate, Smart Circuit loads moved over. Add a day for a panel upgrade or a long conduit run.
- Inspection and PTO. We meet the inspector, submit the sign-off, and PG&E's Permission to Operate normally arrives a few weeks later.
- Handover. The FranklinWH app on your own account, Time of Use mode set for NEM 3.0, reserve and generator thresholds chosen with you, Smart Circuits named, and a live test of what stays on when we open the main.
Where we install FranklinWH
Our crew works out of Los Gatos, so Santa Clara County and the Peninsula are daily territory: San Jose, Los Gatos, Saratoga, Campbell, Cupertino, Sunnyvale, Santa Clara, Mountain View and Palo Alto. San Francisco and Oakland are scheduled-project areas, and the Santa Cruz Mountain side of Highway 17 is where most of our generator-plus-battery jobs sit. Not sure you are in range? The ZIP checker answers in a second.
Our Guarantees
✓ Upfront, No-Surprises Pricing
The price we quote is the price for the agreed scope. If the scope or equipment changes, we agree any adjustment in writing first — never a surprise.
✓ On-Time Guarantee
We show up when we say we will, and keep you posted if anything changes.
✓ Satisfaction Guarantee
We're not finished until you're satisfied with the work.
✓ 10-Year Workmanship Warranty
Our installation labor is guaranteed for 10 years — on top of 25-year equipment warranties.
✓ Price-Match Promise: bring us a written quote from another licensed contractor and we'll beat it by at least 5%.
FAQs — FranklinWH battery installation in the Bay Area
How much does a FranklinWH aPower 2 cost installed in the Bay Area?
$9,000 to $20,000 per aPower 2 before incentives, which is the published range for every home battery we install. A single unit backing up the whole house through an aGate mounted next to an existing 200A panel sits in the lower half; a long conduit run to a detached meter, a Smart Circuits module, a generator module or panel work pushes a quote toward the top. You get one fixed, itemized price after a site visit.
Is the FranklinWH hardware included in that price?
Yes. FranklinWH's hardware pricing is set by the manufacturer and included in our fixed quote, along with the aGate, mounting, wiring, the permit drawings, inspection and the PG&E interconnection application. Items quoted on top only when you need them: a second aPower 2, the generator module, Smart Circuits, a 200A panel upgrade at $4,500 to $14,000, or new solar at $20,000 to $50,000.
How many aPower 2 units does a Bay Area home need?
One for most single-family homes. The aPower 2 holds 15 kWh and delivers 10 kW continuous with a 15 kW ten-second surge, so a single unit runs a refrigerator, lights, internet, a furnace fan and a well pump overnight and can start a central air-conditioning compressor. Two units make sense for all-electric homes with a heat pump, induction cooking and an EV charger, or for anyone who wants air conditioning through a multi-day shutoff. FranklinWH allows up to 15 units on one aGate.
Can I add a FranklinWH battery to the solar I already have?
Yes, and this is the job FranklinWH is best at. The aPower 2 is AC-coupled, so your existing inverter stays exactly where it is and the battery charges from its AC output; the aGate datasheet lists compatibility with both micro- and string inverters, which covers Enphase, SolarEdge, SMA, Fronius and the rest. We check the array's output against the aGate's 80A solar input and the per-unit PV limit before quoting, then add the battery without touching your roof.
Does the aGate really start a generator by itself?
Yes, with FranklinWH's optional generator module. You set an upper and lower battery state of charge in the app; when the battery drops to the low mark during an outage and solar is not covering the house, the aGate sends a two-wire start signal to the standby generator, the generator carries the loads and recharges the battery, and it shuts down again at the high mark. The module accepts generators up to 160A continuous and also supports utility-sense and ATS-style units.
What are Smart Circuits and do I need them?
Smart Circuits are controllable breaker positions inside the aGate (one 80A and up to two 50A circuits) that the system can shed automatically during an outage or that you can switch from the FranklinWH app. We wire the EV charger, the pool pump or an air-conditioning condenser to them so they stop drawing from the battery when it runs low and come back when solar or the generator catches up. If none of those loads is in your backup plan, skip the module and keep the price down.
Will FranklinWH keep my house running through a PG&E PSPS shutoff?
Yes, for the loads it is sized to carry. The aGate acts as the microgrid interconnect device: when PG&E de-energizes the line it isolates the house, the aPower 2 picks up the loads without a flicker, and your solar recharges it the next morning. With one unit, plan on everything except central air conditioning through a two- or three-day shutoff; with two units, or one unit plus a generator on the module, air conditioning stays on the list.
FranklinWH or Tesla Powerwall 3: which one should I buy?
Choose FranklinWH when you are adding storage to solar you already own, when a standby generator is part of the plan, or when you want the 15-year warranty and room to grow in 15 kWh steps. Choose a Powerwall 3 when you are buying new solar and battery together, because its built-in solar inverter saves one piece of equipment and one line on the permit. We are certified for both and quote the one that fits; our Powerwall 3 page covers the Tesla side in the same detail.
Is there a rebate or tax credit for a FranklinWH battery in California in 2026?
For most households, no. The residential 30% federal credit ended for systems placed in service after December 31, 2025, and every residential SGIP battery budget has been closed or waitlisted since September 2026. Income-qualified households at or below 80% of area median income, or enrolled in CARE, FERA or ESA, can still join the SGIP equity waitlist, which we file for you. Businesses and non-profits keep the commercial Investment Tax Credit. We never price a battery around a rebate that may not pay.
How long does a FranklinWH installation take, including PG&E?
One to two days on site for most homes: the aGate goes in at the service entrance or beside the main panel, the aPower 2 mounts on the wall or floor next to it, and the solar and generator connections land in the aGate. Before that, the city or county permit and the PG&E interconnection application take two to six weeks depending on the jurisdiction, and Permission to Operate follows the final inspection. Plan on four to eight weeks from signed contract to a working battery.
Request Your Free Quote
Licensed, bonded & insured Bay Area electricians. Upfront pricing and same-day estimates available.
CA Lic #1143455 · Tesla Certified Installer · Enphase · Bonded & Insured
✓ 10-year workmanship warranty · ✓ Our own licensed C-10 crew — no subcontractors · ✓ Upfront, no-pressure pricing
Get a Free Quote ☎ (650) 451-8464